HONDA FOREMAN 500 ATV REPAIR / FINAL DRIVE UNIVERSAL JOINT AND SWING ARM INSTALLATION / TECH TIPS

HONDA ATV’S IN MY OPINION ARE BULLET PROOF IF LEFT ALONE IN THE FACTORY CONFIGURATION IT WAS BORN WITH / ADDING LIFT KITS AND HEAVY OVERSIZE TIRES WITH DEEP …

20 Comments

  1. 0
    Posted 01/23/2015 at 7:34 | Permalink

    Excellent Job Buddy! Thoroughly loved your video. Thanks! I was wondering how
    much difference there is from this 500 and a 2002 Foreman 450…Would you
    by chance know? It looks like I may be purchasing a 2002 450 S….Im trying
    to pick up all the pointers I can get because I dont know what all it was
    used for or went through since it was uncrated 13 years ago…

  2. 0
    Posted 01/23/2015 at 8:26 | Permalink

    man im having vex getting the ancient bearings out. how did you get yours
    out?????? please help

  3. 0
    Posted 01/23/2015 at 9:18 | Permalink

    Fantastic video! Helped me out a lot since my u joint went out on my 06 Foreman
    500!!

  4. 0
    Posted 01/23/2015 at 10:01 | Permalink

    I have vex with swing arm bearings, would pulling a trailer cause this?
    Is there a surpass after market bearing I could use?

  5. 0
    Posted 01/23/2015 at 10:47 | Permalink

    That looks like a CDI torque wrench. I’m in the market for one. Could you
    tell the develop #? 1/2″ right?

  6. 0
    Posted 01/23/2015 at 11:10 | Permalink

    what size ir the axle nut?

  7. 0
    Posted 01/23/2015 at 11:15 | Permalink

    I am just doing swing arm bearings, do you need to disassemble the whole
    differential or can i juts disconnect the shock and brake and upper swing
    arm bolts in order to take out?

  8. 0
    Posted 01/23/2015 at 11:22 | Permalink

    Hey man so I have a 03 raptor 660 that turns over but won’t start without
    choke then when the choke is on it turns on please help I don’t know what
    the problem is 

  9. 0
    Posted 01/23/2015 at 11:46 | Permalink

    Is it necessary to hold the right side bearing nut that is torqued to
    7ft.lbs. while torquing the jamnut to 85 ft lbs? I noticed you did not, and
    I would reckon it will turn with the jamnut over torquing the bearings. ?

  10. 0
    Posted 01/23/2015 at 12:06 | Permalink

    Excellent luck with the house and shop. Show some videos of the shop and reasons
    for a new shop. Thanks

  11. 0
    Posted 01/23/2015 at 12:53 | Permalink

    thanks for the video.
    Bruce from Canada

  12. 0
    Posted 01/23/2015 at 13:20 | Permalink

    Merry Christmas and pleased new year!

  13. 0
    Posted 01/23/2015 at 13:43 | Permalink

    what is the product nr of that Loctite sealant? =)

  14. 0
    Posted 01/23/2015 at 14:04 | Permalink

    Smashing repair :-))

    You and your family have a smashing christmas and a fruitfull new year :-))

  15. 0
    Posted 01/23/2015 at 14:21 | Permalink

    merry Christmas to you and yours Jeremy.

  16. 0
    Posted 01/23/2015 at 15:14 | Permalink

    For you too, Merry Christmas and pleased new year!

  17. 0
    Posted 01/23/2015 at 15:24 | Permalink

    Merry Christmas

  18. 0
    Posted 01/23/2015 at 15:41 | Permalink

    Excellent video

  19. 0
    Posted 01/23/2015 at 15:52 | Permalink

    I am replacing the swingarm bearings in my honda recon and after installing
    i noticed that at the housing the gap is different between the right and
    left side of the frame? Not much but enough to tell, the swingarm is tight
    and seems to be locked in just wondering if you knew whatever thing about that?

  20. 0
    Posted 01/23/2015 at 16:28 | Permalink

    What ever happen to this guy? No more videos